Splicing adhesive refers to the adhesive used for splicing integrated materials and other wooden products, suitable for splicing adhesive for non-structural materials and structural material integrated materials. The main component of splicing adhesive is polyvinyl acetate emulsion, which has special waterproof effects. The curing agent is generally isocyanate. The color is milky white viscous liquid, and the curing agent is light brown. The main component of splicing adhesive can generally be used alone as finger joint adhesive.

How to correctly use splicing adhesive?

The characteristics of adhesive bonding using marble adhesive combined with curing agent form a two-component adhesive. Its characteristics are fast gelation speed, short curing time, high bonding strength, and can cure at low temperatures (-10°C). At room temperature, after adjusting the formula, the gel can fully cure within a few seconds, and completely cure in about 5 minutes. According to the ratio of powder:water = 1:0.25-0.3, stir evenly and it is ready for construction. Within the allowable operation time, the position of tiles can be adjusted. After the adhesive is completely dry and cured (filling work can be carried out in about 24 hours, heavy loads should avoid being pressed on the tile surface within 24 hours).

1. Tile adhesive mixed with cement and mortar.

This will completely change the product ratio, product quality cannot be guaranteed, and tile laying is prone to hollowing and tile falling.

Put the tile adhesive on the ground and stir with a shovel.

Stirring with a shovel is uneven, and the effective chemical components in the tile adhesive are lost. At the same time, the ratio of added water during manual stirring is difficult to be accurate, and the material ratio changes, leading to a decrease in bonding strength.

How to correctly use tile adhesive, the seven mistakes of tile adhesive!

The main performance of exterior wall transparent waterproof adhesive depends on its adsorption capacity. Exterior wall transparent waterproof adhesive is aging resistant, does not turn white when soaked in water, does not turn yellow or black over time, and has good strength. The substrate surface must be completely clean, dry, and free of oil and dust. Repair cracks, eliminate honeycomb surfaces, manually brush or high-pressure spray to achieve coverage.

Quick-drying adhesive is characterized by fast curing speed, so the application speed is fast. Some problems may occur when using quick-drying adhesive. 1. When using quick-drying adhesive, you must use a dry cotton cloth or sandpaper to remove dust, oil, and rust from the next surface, then wipe with acetone or trichloroethylene and other cleaning agents, and then clean the adhesive surface. 2. Bottled quick-drying adhesive can be used by simply unscrewing the front cap. If glue is found at the bottle opening after opening, you can first wipe off the glue with a cotton cloth, then use a needle or PE dropper to control the glue flow, ensuring uniformity of glue and bonding effect. 3. Drop a small drop of glue on the next surface, bond immediately, and keep it hard. The hardening time takes 10-60 seconds. If it is a metal-specific adhesive, it may take 30 minutes to achieve practical strength, and curing strength can be reached after 24 hours. 4. After use, clean the bottle opening, tighten the cap, and store directly in a cool, dry place. If it is a metal-specific adhesive, please store it in a cool, dry place.

3. Soak the tile adhesive in a bucket.

Masters are accustomed to using the method of soaking cement. Long-term soaking of mixed tile adhesive on the ground or in a bucket can easily lead to the tile adhesive having no strength, powdering, and tile falling.

How to correctly use tile adhesive, the seven mistakes of tile adhesive!

4. If used for too long, add water and stir.

The effective components of tile adhesive have undergone chemical reactions. Adding water will only change the operational performance, leading to insufficient bonding strength later. Tile adhesive should be stirred and used within 2 hours, and discarded after it hardens.

Can marble adhesive stick tiles? What is the difference between it and tile adhesive? Next, through a comparison with tile adhesive, we briefly analyze the feasibility of marble adhesive for sticking tiles: 1. Product composition: The base material of marble adhesive is unsaturated resin, with epoxy resin and other polymer synthetic materials as the base material. Tile adhesive is a polymer-modified cement-based tile adhesive, divided into type 1 (ordinary), type 2 (enhanced), type 3 (large tiles or marble), and other varieties. In terms of raw materials, there is an essential difference between the two.

So, what are the precautions for using waterproof adhesive? Although the use of waterproof adhesive is very common, this does not mean that there are no concerns about its use. In fact, the use of waterproof adhesive still requires protective measures. After the first use, the product should cover the entire demand, that is, during use, cover the places that need bonding. Second, pay attention to the time of use. Each operation requires 24 hours before other work can be carried out to improve the consolidation of the waterproof adhesive. Third, special responses for special places. If used in situations with high wear resistance requirements, adding a hardened layer to protect the entire appearance from damage is very important.